Credit goes to +Guitrum+ for the featured picture.
__
– Name : G2-CTE Evolved
– Creator : +Guitrum+
– Length : 20-21cm
– Weight : Heavy
– Insert / Outsert : Yes
– Link : G2-CTE Evolved (UPSB v3)
– Making : Hard, long.
– Pens list :
– 1 Zebra Hyperjell (cap)
– 1 Uniball RT (tip + spring + inktube)
– 1 Pilot Dr.Grip Shaker (grip +metal rod)
– 1 Pilot G2 (All parts)
– 1 M&M / ACT / CT / KT (Body)
– 1 Beifa (grip)
– 1 Anyball (grip)
– Tutorial :
1-Cut the Dr. Grip grip, Anyball and Beifa grip like shown below
2- Cut/sand down the front of the G2 small body piece like shown below:
3-Sand the cut G2 small body piece like shown below, then screw on the IRT (=impact rt) tip
4- Use tape to secure one end of an insert to the sanded G2 small body piece then wrap around and apply cut Dr. Grip on top of the insert (there is no need to secure the insert beyond the single piece of tape):
5- Push the completed G2 small body piece into the back of the MM/CT/AC/KT body until it meets the base of the cut Dr. Grip grip. Then apply the 2-ringed section of the cut Profile grip behind and the cut Beifa grip on the IRT tip (apply dabs of superglue if you would like to have a secure fit) like shown below
6- Cut off the knub from the front of the MM/CT/AC/KT body and then sand open the hole until it is wide enough for a G2 inktube to slide freely inside like shown below:
7- Dismantle the Hyperjell cap and remove the clip like shown below, then proceed to cut off the top of the cap where the 2 square shaped holes are (do not cut farther below):
8- Slide an insert inbetween the Hyperjell cap and the G2 body and push it all the way in until it stops. Trim off the extra paper then the cut away the excess G2 body and sand until it meets the base of the Hyperjell cap like shown below:
9- Insert the clickers back into the cut G2 large body piece, apply the middle 3-ringed cut piece of Profile grip to the end of Hyperjell cap, apply the end 3-ringed cut Profile grip to the MM/CT/AC/KT body, push on the retractable mechanism and finally push the profile grip up to meet the end of the retractable mechanism piece like shown below:
10- Empty out the G2 inktube (keep the plastic stopper) then tape it to the end of the IRT inktube. By use of trial and error, determine how much to cut off of the empty G2 inktube until the mod will retract fully and properly. This will vary for each person but I have shown how long mine was so you can see what I had. Remember to put the plastic stopper back in the empty G2 inktube after each cut
11- Insert the Dr. Grip shaker piece into the cut, empty G2 inktube but push it in far enough for the plastic stopper to fit:
12- Push everything together and congratulations! You have just made a G2-CTE Evolved!
– Comment :
Excuse me for all these images, but without them, it’s very difficult to understand the tutorial :(. Again, congratulations to +Guitrum+ for this wonderful mod o_O maybe a little heavy for those like medium weight mod.
Il m’énerve guitrum. Il fait toujours des mods trop beaux.
salut tout le monde
ou est ce kon pourrai des dr grip shacker
( sur penwish et penstorm il y en a plus)
Go on eBay > http://cgi.ebay.fr/Pilot-Dr-Grip-Shake-Press-HDG-Mechanical-Pencil-PINK-/160466194558?pt=LH_DefaultDomain_2&hash=item255c87d07e
merci pour le site mais ché pas comment acheter sur ebay –‘…….
et aussi j’arrive pas a enlever le clip d’Hyperjell ( j’en ai raté 2 –‘ )
Comment ça ?
ba ché pas avec koi coupé le clip d’hyperjell, jé essayé en le cassant mais le cap s’est cassé aussi. sinon sur ebay c bon jai trouvé
Pour l’enlever totalement, tu peux utiliser un x-acto/couteau (quelque chose de pointu/coupant quoi) et du feu. Tu laisses ton couteau sur le feu pendant 15 sec environ et tu coupe le clip. Le seul probleme de cette technique est qu’il se peut que du plastique reste collé au couteau et celui ci risque de noircir.
Si tu veux seulement enlever le bout (comme pour faire un Kuzu G3 Mod par exemple), tu fais une entaille assez profonde avec un couteau à l’endroit où tu veux qu’il se coupe et tu finis à la main =)
ok merci!
j’en vend un si quelqu’un est interessé 😉
Comments are closed.