Glenn Matthews

Name : Glenn Matthews

Creator : Purplet

Lenght : 20.5 cm

Weigth : 18 g

– Insert : Yes

– Link : Glenn Matthews (UPSB)

Moddaing : Dificult

Pens :

– 2 Hyperjell [ Cap ]
– 1 Gripmatic [ Rubber Mechanism, Grip ]
– 1 G3 [ Body ]
– 2 Plastic Tip || 2x(same!) Metal Tip ==> Results in a heavier Mod with lots of momentum.
– 3 Airfit [ Chrome Ring ]
– 1 HGG [ Tip ]
– Tape
– Hot Glue
– 1 Pilot G2 [ inktube ]
– 1 Commsa Backcap or something alike
– 2 Ring of Grip, take wichever you got, anyball is fine, g2 is fine, if you cut straight any grip is fine.

Tutorial :

1- -File down bumps of the G3 Barrel
-Get a 0,5cm wide piece of a)Grip b)white Body c)a cap. It doesnt matter wich option u choose, u have to like the look and u have to get the material, grip is the easiest to get Option i think.
-Put the “piece” on the G3 front and wrap tape in front ot the “piece” as long as it evens out with the “piece”.

2- Wash out the G2 inktube, cut a piece out of it (the exact length doesnt matter), wrap some grip on the front.
-Slide the G2 inktube in the G3 front

3-Screw a plastic (or metal if u have chosen this option) on the tape on the G2 inktube

4-  Cut a ring of grip and one hyperjell cap.
-Put on the front:
1)Chrome Ring
2)Ring of grip =>slide the chrome ring over the ring of grip. Place this directly after the “piece”.
3)the cut hyperjell cap
4)a ring of grip =>slide this between hyperjell cap and tip
5)Another chrome ring, this one gets directly on the hyperjell cap==>use hot glue//superglue. I use hot glue.

5- Now that you know how to assemble the front, do it again but with the front insert under the cut hyperjell cap 🙂
I can’t give much advise on this, simply try with a plain white paper its not hard to do.
You finished the front.

6–Wrap some tape around the hgg tip.
-Put hgg tip inside the gripmatic grip and wrap the back insert around that. If u use metal tips u have to add one too. In this case put the hgg tip inside the metal tip.
-Insert the gripmatic grip+insert+hggtip(+metal tip) in the cap.
-(hot)glue the chrome ring on the hyperjell cap. U have to do this after inserting the other stuff!

7- -File down any bumps on the comssa backcap. It has to fit (the front part, not the back part) inside the g3 barrel with insert.
How much u have to file down depends on how thick ur papers is and if u use clear tape on the ends of the insert like i do.
Finally, it should fit firm but can be twisted around.
-Cut of a bit (pretty much everything without ink at a fully rsvp inktube…wich isnt pretty muchXD) of the rsvp inktube.
-Glue the inktube in the “screw” of the gripmatic mechanism.
-Glue some (emptied!) piece of inktube in the comssa backcap. As u probably see i use some special backcap, its from some smaller commsa fakes.
-Glue the other side of the piece of inktube on in the “screw”

8–Put the main insert in the g3 barrel
-File down the gripmatic mechanisms main part a bit, again this depends on how thick ur paper is.
Since the g3 body is a bit of a cone it will stick in there as u push it in (use some g2 inktube or a small pencil i.e.).
If its getting too far inside u will have to a)use another gripmatic mechanism and file down less b)use thick paper c)add some hot glue/tape d)adjust the inktube.
I wont recommend option “d” since ull need some smaller inktube (take the one of the airfit ) and a longer piece of empty inktube on the other side of the screw.

9- Insert the inktube in the g3 body, as soon as the “screw” and “main part” of the gripmatic mechanism meet simply screw them together.
U have quiet some space to adjust the whole thing, if it doesnt work adjust the empty inktube part of the mechanism to get the cap further or less on the g3 body.

Comment : A mod that looks to me very frankly with a crazy design o_o

Comments
All comments.
Comments

  1. avatar
    Vôre-Tèx

    @Taeko- + @autres:

    Je t’explique comment marche le sytème de twistabilité. Il y a deux parties dans le sytème du grip matic qu’il faut utiliser :
    – une première partie que tu mets dans le corps du G3 (cette partie est striée)
    – une deuxième partie que tu colles sur l’inktube de RSVP (elle est en forme de spirale et est à l’intérieur de la première partie dans le grip matic)

    Tu vas te dire, mais quel est l’intérêt?
    Eh ben, j’espère que tu a déjà vu comment fonctionne le système de twistabilité de la gomme du grip matic ? Il suffit de tourner la partie striée (dans le tuto, elle est située dans le corps du G3) pour que la gomme sorte.

    L’inventeur de ce mod a donc prit le sytsème du grip matic pour en faire un twistable 🙂

    Voilà, j’espère que j’ai été assez clair ^^

  2. avatar
    peper

    mmmm… le tuto est plutot bien realiser et traduit le seul hic c’est que les tips ne son pas des signo mais des fake en plastoc^^

  3. avatar
    peper

    a j’ai oublier tu a ecrit bicmatic au lieu de gripmatic^^

  4. avatar
    taeko-

    oups ^^” corrigé =)

    J’ai quand même un peu de mal a comprendre comment le système fonctionne, le tuto explique pas trop cette partie la.