Credit goes to Penwish for the featured picture.
__
– Name : Seven G3
– Creator : Seven
– Length : 20 cm
– Weight : 14 g
– Insert : Yes
– Link : Seven’s Mod ( UPSB archive )
– Difficulty : Hard
– Pens :
– 1 Pilot G3 (Plastic ver.) (Body, Tip)
– 1 Zebra Jimnie (Cap)
– 1 Uni-ball Lakubo (Grip)
– 1 Zebra Hyper Jell (Grip) (You can use the Jimnie grip)
– 1 Uni-ball Signo DX (Grip)
– 2 Anyball/Profile (Grip )
– 1 Pentel Hybrid Gel Grip (HGG) (Grip)
– 1 Ohto Metallic Gel (Tip)
– 1 Ohto Needle-Point (Tip)
– 1 Pastel Color (Grip)
– Some Aluminum tape (cellophane tape also works)
– Tutorial :
1- Cut off the clip of the Jimnie cap
2- Cut a section of HGG grip that is about 1 Anyball block long (about 3 mm) and put it into the Jimnie Cap.
3- Put the Signo tip into the cap (its held by the HGG grip)
4- Cut 2.6 cm of Hyper Jell grip and one and a half block (3 mm) of one Anyball grip.
5- Stuff the cut Anyball grip into the cut Hyper Jell grip.
6- Add an insert if desired around the Hyper Jell grip, and put it into the Jimnie cap.
7- Cut 2-3 mm of Pastel Color Grip and put it into the Jimnie cap after the Hyper Jell.
8- Clear the G3 front (remove grip, sand down front) and remove the baclplug. Cut 6 mm of the Signo grip and place it on the G3 front.
9- Cut 2 blocks of Anyball/Profile, unscrew the tip of the G3, and stuff the Anyball section into the G3 front.10- Screw the plastic tip of the G3 back on after you are done stuffing the Anyball grip in. Wrap one round aluminum tape around the front of the G3.
11- Tip stack: Plastic G3 tip> Metallic Gel tip> Needlepoint tip
12- Wrap the tip stack with one round of aluminum tape.
13- Slide the Lakubo grip over the tip stack .
14- Add some tape around the end of the G3 Body so that the Jimnie cap stays on securely. Use the right amount to keep it on to avoid cap cloud. Add an insert of your choice into the G3 barrel.
Complete!
– Comment :
One of the few mods invented before the 2010s and still worldwide famous in 2020. Crazy design, crazy specs and is a classic mod alongside Ryo KT. All of the best spinners have one in their collection.
One of the few mods invented before the 2010s and still worldwide famous in 2020. Crazy design, crazy specs and is a classic mod alongside Ryo KT. All of the best spinners have one in their collection.
Pas si lourd que ça.
Très bon mod.
Cependant, comme le dit Toonet, il n’est pas très lourd ! 14grammes environs.
Thx for tutorial ^^ btw the weight is 14g
Mmmh pourquoi il y a une bande blanche entre le grip avant et le corps ?
C’est du tape ou les 6 millimètres d’un grip de HGG ?
Et aussi, une bande de HGG dans le cap, c’est combien ? ou c’est le petit anneau ?
Et aussi, une bande de grip de HGG dans le cap, c’est combien ? ou c’est le petit anneau ? *
Et euuuh, les Tips de Metallic Gel et Needle Point sont en plastiques ?
Si c’est mettalic gel il sont en métal 😉 (enfin je crois)
Kazrzack, pas mal la réponse 8 mois après XD
Mais pour répondre à la question de Aka, les tips sont en plastiques (je le sais car j’ai un metallic gel chez moi et le tip est bien en plastique 😉 )
Il est équilibré ?
HypperGel ou hpper jell ?
Jimnie Gel pour être exact 😛
L’Hyper Jell est un fake, en fait 🙂
Il est équilibrer ?
SI non de quelle coter il est plus lourd ?